80 lines
2.4 KiB
Arduino
80 lines
2.4 KiB
Arduino
|
/*
|
||
|
|
* This sketch demonstrates how to scan WiFi networks.
|
||
|
|
* The API is almost the same as with the WiFi Shield library,
|
||
|
|
* the most obvious difference being the different file you need to include:
|
||
|
|
*/
|
||
|
|
#include "WiFi.h"
|
||
|
|
|
||
|
|
/* These are the GPIOs connected to the antenna switch on the ESP32-WROOM-DA.
|
||
|
|
* Both GPIOs are not exposed to the module pins and cannot be used except to
|
||
|
|
* control the antnnas switch.
|
||
|
|
*
|
||
|
|
* For more details, see the datashhet at:
|
||
|
|
* https://www.espressif.com/sites/default/files/documentation/esp32-wroom-da_datasheet_en.pdf
|
||
|
|
*/
|
||
|
|
|
||
|
|
#define GPIO_ANT1 2 // GPIO for antenna 1
|
||
|
|
#define GPIO_ANT2 25 // GPIO for antenna 2 (default)
|
||
|
|
|
||
|
|
void setup()
|
||
|
|
{
|
||
|
|
bool err = false;
|
||
|
|
Serial.begin(115200);
|
||
|
|
|
||
|
|
// Set WiFi to station mode and disconnect from an AP if it was previously connected
|
||
|
|
WiFi.mode(WIFI_STA);
|
||
|
|
|
||
|
|
/* Attention: This is the manual prodecure for the dual antenna configuration.
|
||
|
|
* If you choose the ESP32-WROOM-DA module from the Tools -> Board, this configuration
|
||
|
|
* is not necessary!
|
||
|
|
*
|
||
|
|
* Set WiFi dual antenna configuration by passing the GPIO and antenna mode for RX ant TX
|
||
|
|
*/
|
||
|
|
err = WiFi.setDualAntennaConfig(GPIO_ANT1, GPIO_ANT2, WIFI_RX_ANT_AUTO, WIFI_TX_ANT_AUTO);
|
||
|
|
|
||
|
|
/* For more details on how to use this feature, see our docs:
|
||
|
|
* https://docs.espressif.com/projects/arduino-esp32/en/latest/api/wifi.html
|
||
|
|
*/
|
||
|
|
|
||
|
|
if(err == false) {
|
||
|
|
Serial.println("Dual Antenna configuration failed!");
|
||
|
|
} else {
|
||
|
|
Serial.println("Dual Antenna configuration successfuly done!");
|
||
|
|
}
|
||
|
|
|
||
|
|
WiFi.disconnect();
|
||
|
|
delay(100);
|
||
|
|
|
||
|
|
Serial.println("Setup done");
|
||
|
|
}
|
||
|
|
|
||
|
|
void loop()
|
||
|
|
{
|
||
|
|
Serial.println("scan start");
|
||
|
|
|
||
|
|
// WiFi.scanNetworks will return the number of networks found
|
||
|
|
int n = WiFi.scanNetworks();
|
||
|
|
Serial.println("scan done");
|
||
|
|
if (n == 0) {
|
||
|
|
Serial.println("no networks found");
|
||
|
|
} else {
|
||
|
|
Serial.print(n);
|
||
|
|
Serial.println(" networks found");
|
||
|
|
for (int i = 0; i < n; ++i) {
|
||
|
|
// Print SSID and RSSI for each network found
|
||
|
|
Serial.print(i + 1);
|
||
|
|
Serial.print(": ");
|
||
|
|
Serial.print(WiFi.SSID(i));
|
||
|
|
Serial.print(" (");
|
||
|
|
Serial.print(WiFi.RSSI(i));
|
||
|
|
Serial.print(")");
|
||
|
|
Serial.println((WiFi.encryptionType(i) == WIFI_AUTH_OPEN)?" ":"*");
|
||
|
|
delay(10);
|
||
|
|
}
|
||
|
|
}
|
||
|
|
Serial.println("");
|
||
|
|
|
||
|
|
// Wait a bit before scanning again
|
||
|
|
delay(5000);
|
||
|
|
}
|