101 lines
2.6 KiB
Arduino
101 lines
2.6 KiB
Arduino
|
#include "freertos/FreeRTOS.h"
|
||
|
|
#include "freertos/task.h"
|
||
|
|
#include "freertos/event_groups.h"
|
||
|
|
#include "Arduino.h"
|
||
|
|
|
||
|
|
#include "esp32-hal.h"
|
||
|
|
|
||
|
|
// The effect seen in ESP32C3, ESP32S2 and ESP32S3 is like a Blink of RGB LED
|
||
|
|
#if CONFIG_IDF_TARGET_ESP32S2
|
||
|
|
#define BUILTIN_RGBLED_PIN 18
|
||
|
|
#elif CONFIG_IDF_TARGET_ESP32S3
|
||
|
|
#define BUILTIN_RGBLED_PIN 48
|
||
|
|
#elif CONFIG_IDF_TARGET_ESP32C3
|
||
|
|
#define BUILTIN_RGBLED_PIN 8
|
||
|
|
#else
|
||
|
|
#define BUILTIN_RGBLED_PIN 21 // ESP32 has no builtin RGB LED
|
||
|
|
#endif
|
||
|
|
|
||
|
|
#define NR_OF_LEDS 8*4
|
||
|
|
#define NR_OF_ALL_BITS 24*NR_OF_LEDS
|
||
|
|
|
||
|
|
//
|
||
|
|
// Note: This example uses Neopixel LED board, 32 LEDs chained one
|
||
|
|
// after another, each RGB LED has its 24 bit value
|
||
|
|
// for color configuration (8b for each color)
|
||
|
|
//
|
||
|
|
// Bits encoded as pulses as follows:
|
||
|
|
//
|
||
|
|
// "0":
|
||
|
|
// +-------+ +--
|
||
|
|
// | | |
|
||
|
|
// | | |
|
||
|
|
// | | |
|
||
|
|
// ---| |--------------|
|
||
|
|
// + + +
|
||
|
|
// | 0.4us | 0.85 0us |
|
||
|
|
//
|
||
|
|
// "1":
|
||
|
|
// +-------------+ +--
|
||
|
|
// | | |
|
||
|
|
// | | |
|
||
|
|
// | | |
|
||
|
|
// | | |
|
||
|
|
// ---+ +-------+
|
||
|
|
// | 0.8us | 0.4us |
|
||
|
|
|
||
|
|
rmt_data_t led_data[NR_OF_ALL_BITS];
|
||
|
|
|
||
|
|
rmt_obj_t* rmt_send = NULL;
|
||
|
|
|
||
|
|
void setup()
|
||
|
|
{
|
||
|
|
Serial.begin(115200);
|
||
|
|
|
||
|
|
if ((rmt_send = rmtInit(BUILTIN_RGBLED_PIN, RMT_TX_MODE, RMT_MEM_64)) == NULL)
|
||
|
|
{
|
||
|
|
Serial.println("init sender failed\n");
|
||
|
|
}
|
||
|
|
|
||
|
|
float realTick = rmtSetTick(rmt_send, 100);
|
||
|
|
Serial.printf("real tick set to: %fns\n", realTick);
|
||
|
|
|
||
|
|
}
|
||
|
|
|
||
|
|
int color[] = { 0x55, 0x11, 0x77 }; // RGB value
|
||
|
|
int led_index = 0;
|
||
|
|
|
||
|
|
void loop()
|
||
|
|
{
|
||
|
|
// Init data with only one led ON
|
||
|
|
int led, col, bit;
|
||
|
|
int i=0;
|
||
|
|
for (led=0; led<NR_OF_LEDS; led++) {
|
||
|
|
for (col=0; col<3; col++ ) {
|
||
|
|
for (bit=0; bit<8; bit++){
|
||
|
|
if ( (color[col] & (1<<(7-bit))) && (led == led_index) ) {
|
||
|
|
led_data[i].level0 = 1;
|
||
|
|
led_data[i].duration0 = 8;
|
||
|
|
led_data[i].level1 = 0;
|
||
|
|
led_data[i].duration1 = 4;
|
||
|
|
} else {
|
||
|
|
led_data[i].level0 = 1;
|
||
|
|
led_data[i].duration0 = 4;
|
||
|
|
led_data[i].level1 = 0;
|
||
|
|
led_data[i].duration1 = 8;
|
||
|
|
}
|
||
|
|
i++;
|
||
|
|
}
|
||
|
|
}
|
||
|
|
}
|
||
|
|
// make the led travel in the pannel
|
||
|
|
if ((++led_index)>=NR_OF_LEDS) {
|
||
|
|
led_index = 0;
|
||
|
|
}
|
||
|
|
|
||
|
|
// Send the data
|
||
|
|
rmtWrite(rmt_send, led_data, NR_OF_ALL_BITS);
|
||
|
|
|
||
|
|
delay(100);
|
||
|
|
}
|