90 lines
2.6 KiB
Arduino
90 lines
2.6 KiB
Arduino
|
#if ARDUINO_USB_MODE
|
||
|
|
#warning This sketch should be used when USB is in OTG mode
|
||
|
|
void setup(){}
|
||
|
|
void loop(){}
|
||
|
|
#else
|
||
|
|
#include "USB.h"
|
||
|
|
|
||
|
|
#if ARDUINO_USB_CDC_ON_BOOT
|
||
|
|
#define HWSerial Serial0
|
||
|
|
#define USBSerial Serial
|
||
|
|
#else
|
||
|
|
#define HWSerial Serial
|
||
|
|
USBCDC USBSerial;
|
||
|
|
#endif
|
||
|
|
|
||
|
|
static void usbEventCallback(void* arg, esp_event_base_t event_base, int32_t event_id, void* event_data){
|
||
|
|
if(event_base == ARDUINO_USB_EVENTS){
|
||
|
|
arduino_usb_event_data_t * data = (arduino_usb_event_data_t*)event_data;
|
||
|
|
switch (event_id){
|
||
|
|
case ARDUINO_USB_STARTED_EVENT:
|
||
|
|
HWSerial.println("USB PLUGGED");
|
||
|
|
break;
|
||
|
|
case ARDUINO_USB_STOPPED_EVENT:
|
||
|
|
HWSerial.println("USB UNPLUGGED");
|
||
|
|
break;
|
||
|
|
case ARDUINO_USB_SUSPEND_EVENT:
|
||
|
|
HWSerial.printf("USB SUSPENDED: remote_wakeup_en: %u\n", data->suspend.remote_wakeup_en);
|
||
|
|
break;
|
||
|
|
case ARDUINO_USB_RESUME_EVENT:
|
||
|
|
HWSerial.println("USB RESUMED");
|
||
|
|
break;
|
||
|
|
|
||
|
|
default:
|
||
|
|
break;
|
||
|
|
}
|
||
|
|
} else if(event_base == ARDUINO_USB_CDC_EVENTS){
|
||
|
|
arduino_usb_cdc_event_data_t * data = (arduino_usb_cdc_event_data_t*)event_data;
|
||
|
|
switch (event_id){
|
||
|
|
case ARDUINO_USB_CDC_CONNECTED_EVENT:
|
||
|
|
HWSerial.println("CDC CONNECTED");
|
||
|
|
break;
|
||
|
|
case ARDUINO_USB_CDC_DISCONNECTED_EVENT:
|
||
|
|
HWSerial.println("CDC DISCONNECTED");
|
||
|
|
break;
|
||
|
|
case ARDUINO_USB_CDC_LINE_STATE_EVENT:
|
||
|
|
HWSerial.printf("CDC LINE STATE: dtr: %u, rts: %u\n", data->line_state.dtr, data->line_state.rts);
|
||
|
|
break;
|
||
|
|
case ARDUINO_USB_CDC_LINE_CODING_EVENT:
|
||
|
|
HWSerial.printf("CDC LINE CODING: bit_rate: %u, data_bits: %u, stop_bits: %u, parity: %u\n", data->line_coding.bit_rate, data->line_coding.data_bits, data->line_coding.stop_bits, data->line_coding.parity);
|
||
|
|
break;
|
||
|
|
case ARDUINO_USB_CDC_RX_EVENT:
|
||
|
|
HWSerial.printf("CDC RX [%u]:", data->rx.len);
|
||
|
|
{
|
||
|
|
uint8_t buf[data->rx.len];
|
||
|
|
size_t len = USBSerial.read(buf, data->rx.len);
|
||
|
|
HWSerial.write(buf, len);
|
||
|
|
}
|
||
|
|
HWSerial.println();
|
||
|
|
break;
|
||
|
|
case ARDUINO_USB_CDC_RX_OVERFLOW_EVENT:
|
||
|
|
HWSerial.printf("CDC RX Overflow of %d bytes", data->rx_overflow.dropped_bytes);
|
||
|
|
break;
|
||
|
|
|
||
|
|
default:
|
||
|
|
break;
|
||
|
|
}
|
||
|
|
}
|
||
|
|
}
|
||
|
|
|
||
|
|
void setup() {
|
||
|
|
HWSerial.begin(115200);
|
||
|
|
HWSerial.setDebugOutput(true);
|
||
|
|
|
||
|
|
USB.onEvent(usbEventCallback);
|
||
|
|
USBSerial.onEvent(usbEventCallback);
|
||
|
|
|
||
|
|
USBSerial.begin();
|
||
|
|
USB.begin();
|
||
|
|
}
|
||
|
|
|
||
|
|
void loop() {
|
||
|
|
while(HWSerial.available()){
|
||
|
|
size_t l = HWSerial.available();
|
||
|
|
uint8_t b[l];
|
||
|
|
l = HWSerial.read(b, l);
|
||
|
|
USBSerial.write(b, l);
|
||
|
|
}
|
||
|
|
}
|
||
|
|
#endif /* ARDUINO_USB_MODE */
|