83 lines
2.4 KiB
Arduino
83 lines
2.4 KiB
Arduino
|
/*
|
||
|
|
Deep Sleep with External Wake Up
|
||
|
|
=====================================
|
||
|
|
This code displays how to use deep sleep with
|
||
|
|
an external trigger as a wake up source and how
|
||
|
|
to store data in RTC memory to use it over reboots
|
||
|
|
|
||
|
|
This code is under Public Domain License.
|
||
|
|
|
||
|
|
Hardware Connections
|
||
|
|
======================
|
||
|
|
Push Button to GPIO 33 pulled down with a 10K Ohm
|
||
|
|
resistor
|
||
|
|
|
||
|
|
NOTE:
|
||
|
|
======
|
||
|
|
Only RTC IO can be used as a source for external wake
|
||
|
|
source. They are pins: 0,2,4,12-15,25-27,32-39.
|
||
|
|
|
||
|
|
Author:
|
||
|
|
Pranav Cherukupalli <cherukupallip@gmail.com>
|
||
|
|
*/
|
||
|
|
|
||
|
|
#define BUTTON_PIN_BITMASK 0x200000000 // 2^33 in hex
|
||
|
|
|
||
|
|
RTC_DATA_ATTR int bootCount = 0;
|
||
|
|
|
||
|
|
/*
|
||
|
|
Method to print the reason by which ESP32
|
||
|
|
has been awaken from sleep
|
||
|
|
*/
|
||
|
|
void print_wakeup_reason(){
|
||
|
|
esp_sleep_wakeup_cause_t wakeup_reason;
|
||
|
|
|
||
|
|
wakeup_reason = esp_sleep_get_wakeup_cause();
|
||
|
|
|
||
|
|
switch(wakeup_reason)
|
||
|
|
{
|
||
|
|
case ESP_SLEEP_WAKEUP_EXT0 : Serial.println("Wakeup caused by external signal using RTC_IO"); break;
|
||
|
|
case ESP_SLEEP_WAKEUP_EXT1 : Serial.println("Wakeup caused by external signal using RTC_CNTL"); break;
|
||
|
|
case ESP_SLEEP_WAKEUP_TIMER : Serial.println("Wakeup caused by timer"); break;
|
||
|
|
case ESP_SLEEP_WAKEUP_TOUCHPAD : Serial.println("Wakeup caused by touchpad"); break;
|
||
|
|
case ESP_SLEEP_WAKEUP_ULP : Serial.println("Wakeup caused by ULP program"); break;
|
||
|
|
default : Serial.printf("Wakeup was not caused by deep sleep: %d\n",wakeup_reason); break;
|
||
|
|
}
|
||
|
|
}
|
||
|
|
|
||
|
|
void setup(){
|
||
|
|
Serial.begin(115200);
|
||
|
|
delay(1000); //Take some time to open up the Serial Monitor
|
||
|
|
|
||
|
|
//Increment boot number and print it every reboot
|
||
|
|
++bootCount;
|
||
|
|
Serial.println("Boot number: " + String(bootCount));
|
||
|
|
|
||
|
|
//Print the wakeup reason for ESP32
|
||
|
|
print_wakeup_reason();
|
||
|
|
|
||
|
|
/*
|
||
|
|
First we configure the wake up source
|
||
|
|
We set our ESP32 to wake up for an external trigger.
|
||
|
|
There are two types for ESP32, ext0 and ext1 .
|
||
|
|
ext0 uses RTC_IO to wakeup thus requires RTC peripherals
|
||
|
|
to be on while ext1 uses RTC Controller so doesnt need
|
||
|
|
peripherals to be powered on.
|
||
|
|
Note that using internal pullups/pulldowns also requires
|
||
|
|
RTC peripherals to be turned on.
|
||
|
|
*/
|
||
|
|
esp_sleep_enable_ext0_wakeup(GPIO_NUM_33,1); //1 = High, 0 = Low
|
||
|
|
|
||
|
|
//If you were to use ext1, you would use it like
|
||
|
|
//esp_sleep_enable_ext1_wakeup(BUTTON_PIN_BITMASK,ESP_EXT1_WAKEUP_ANY_HIGH);
|
||
|
|
|
||
|
|
//Go to sleep now
|
||
|
|
Serial.println("Going to sleep now");
|
||
|
|
esp_deep_sleep_start();
|
||
|
|
Serial.println("This will never be printed");
|
||
|
|
}
|
||
|
|
|
||
|
|
void loop(){
|
||
|
|
//This is not going to be called
|
||
|
|
}
|