Prvni ulozeni z chegewara githubu

libraries/WiFi/examples/WiFiScan/README.md

@@ -0,0 +1,73 @@
+# WiFiScan Example
+
+This example demonstrates how to use the WiFi library to scan available WiFi networks and print the results.
+
+# Supported Targets
+
+Currently this example supports the following targets.
+
+| Supported Targets | ESP32 | ESP32-S2 | ESP32-C3 |
+| ----------------- | ----- | -------- | -------- |
+
+## How to Use Example
+
+* How to install the Arduino IDE: [Install Arduino IDE](https://github.com/espressif/arduino-esp32/tree/master/docs/arduino-ide).
+
+#### Using Arduino IDE
+
+* Before Compile/Verify, select the correct board: `Tools -> Board`.
+* Select the COM port: `Tools -> Port: xxx` where the `xxx` is the detected COM port.
+
+#### Using Platform IO
+
+* Select the COM port: `Devices` or setting the `upload_port` option on the `platformio.ini` file.
+
+## Example/Log Output
+
+```
+ets Jul 29 2019 12:21:46
+
+rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
+configsip: 0, SPIWP:0xee
+clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
+mode:DIO, clock div:1
+load:0x3fff0030,len:1412
+load:0x40078000,len:13400
+load:0x40080400,len:3672
+entry 0x400805f8
+Setup done
+scan start
+scan done
+17 networks found
+1: IoTNetwork (-62)*
+2: WiFiSSID (-62)*
+3: B3A7992 (-63)*
+4: WiFi (-63) 
+5: IoTNetwork2 (-64)*
+...
+```
+
+## Troubleshooting
+
+***Important: Be sure you're using a good quality USB cable and you have enought power source for your project.***
+
+* **Programming Fail:** If the programming/flash procedure fails, try to reduce the serial connection speed.
+* **COM port not detected:** Check the USB cable connection and the USB to Serial driver installation.
+
+If the error persist, you can ask help at the official [ESP32 forum](https://esp32.com) or see [Contribute](#contribute).
+
+## Contribute
+
+To know how to contribute to this project, see [How to contribute.](https://github.com/espressif/arduino-esp32/blob/master/CONTRIBUTING.rst)
+
+If you have any **feedback** or **issue** to report on this example/library, please open an issue or fix it by creating a new PR. Contributions are more than welcome!
+
+Before creating a new issue, be sure to try the Troubleshooting and to check if the same issue was already created by someone else.
+
+## Resources
+
+* Arduino-ESP32 Official Repository: [espressif/arduino-esp32](https://github.com/espressif/arduino-esp32)
+* ESP32 Datasheet: [Link to datasheet](https://www.espressif.com/sites/default/files/documentation/esp32_datasheet_en.pdf)
+* ESP32-S2 Datasheet: [Link to datasheet](https://www.espressif.com/sites/default/files/documentation/esp32-s2_datasheet_en.pdf)
+* ESP32-C3 Datasheet: [Link to datasheet](https://www.espressif.com/sites/default/files/documentation/esp32-c3_datasheet_en.pdf)
+* Official ESP-IDF documentation: [ESP-IDF](https://idf.espressif.com)

libraries/WiFi/examples/WiFiScan/WiFiScan.ino

@@ -0,0 +1,48 @@
+/*
+ *  This sketch demonstrates how to scan WiFi networks.
+ *  The API is almost the same as with the WiFi Shield library,
+ *  the most obvious difference being the different file you need to include:
+ */
+#include "WiFi.h"
+
+void setup()
+{
+    Serial.begin(115200);
+
+    // Set WiFi to station mode and disconnect from an AP if it was previously connected
+    WiFi.mode(WIFI_STA);
+    WiFi.disconnect();
+    delay(100);
+
+    Serial.println("Setup done");
+}
+
+void loop()
+{
+    Serial.println("scan start");
+
+    // WiFi.scanNetworks will return the number of networks found
+    int n = WiFi.scanNetworks();
+    Serial.println("scan done");
+    if (n == 0) {
+        Serial.println("no networks found");
+    } else {
+        Serial.print(n);
+        Serial.println(" networks found");
+        for (int i = 0; i < n; ++i) {
+            // Print SSID and RSSI for each network found
+            Serial.print(i + 1);
+            Serial.print(": ");
+            Serial.print(WiFi.SSID(i));
+            Serial.print(" (");
+            Serial.print(WiFi.RSSI(i));
+            Serial.print(")");
+            Serial.println((WiFi.encryptionType(i) == WIFI_AUTH_OPEN)?" ":"*");
+            delay(10);
+        }
+    }
+    Serial.println("");
+
+    // Wait a bit before scanning again
+    delay(5000);
+}