154 lines
5.4 KiB
ReStructuredText
154 lines
5.4 KiB
ReStructuredText
################
|
||
ESP32-S2-Saola-1
|
||
################
|
||
|
||
The `ESP32-S2-Saola-1`_ development board is one of Espressif's official boards. This board is based on the `ESP32-S2-WROVER`_ module, with the `ESP32-S2`_ as the core.
|
||
|
||
Specifications
|
||
--------------
|
||
|
||
- Wi-Fi 802.11 b/g/n (802.11n up to 150 Mbps)
|
||
- Built around ESP32-S2 series of SoCs Xtensa® single-core
|
||
- Integrated 4 MB SPI flash
|
||
- Integrated 2 MB PSRAM
|
||
- Peripherals
|
||
- 43 × programmable GPIOs
|
||
- 2 × 13-bit SAR ADCs, up to 20 channels
|
||
- 2 × 8-bit DAC
|
||
- 14 × touch sensing IOs
|
||
- 4 × SPI
|
||
- 1 × I2S
|
||
- 2 × I2C
|
||
- 2 × UART
|
||
- RMT (TX/RX)
|
||
- LED PWM controller, up to 8 channels
|
||
- 1 × full-speed USB OTG
|
||
- 1 × temperature sensor
|
||
- 1 × DVP 8/16 camera interface, implemented using the hardware resources of I2S
|
||
- 1 × LCD interface (8-bit serial RGB/8080/6800), implemented using the hardware resources of SPI2
|
||
- 1 × LCD interface (8/16/24-bit parallel), implemented using the hardware resources of I2S
|
||
- 1 × TWAI® controller (compatible with ISO 11898-1)
|
||
- Onboard PCB antenna or external antenna connector
|
||
|
||
Header Block
|
||
------------
|
||
|
||
.. note::
|
||
Not all of the chip pins are exposed to the pin headers.
|
||
|
||
J2
|
||
^^^
|
||
=== ==== ===== ===================================
|
||
No. Name Type Function
|
||
=== ==== ===== ===================================
|
||
1 3V3 P 3.3 V power supply
|
||
2 IO0 I/O GPIO0, Boot
|
||
3 IO1 I/O GPIO1, ADC1_CH0, TOUCH_CH1
|
||
4 IO2 I/O GPIO2, ADC1_CH1, TOUCH_CH2
|
||
5 IO3 I/O GPIO3, ADC1_CH2, TOUCH_CH3
|
||
6 IO4 I/O GPIO4, ADC1_CH3, TOUCH_CH4
|
||
7 IO5 I/O GPIO5, ADC1_CH4, TOUCH_CH5
|
||
8 IO6 I/O GPIO6, ADC1_CH5, TOUCH_CH6
|
||
9 IO7 I/O GPIO7, ADC1_CH6, TOUCH_CH7
|
||
10 IO8 I/O GPIO8, ADC1_CH7, TOUCH_CH8
|
||
11 IO9 I/O GPIO9, ADC1_CH8, TOUCH_CH9
|
||
12 IO10 I/O GPIO10, ADC1_CH9, TOUCH_CH10
|
||
13 IO11 I/O GPIO11, ADC2_CH0, TOUCH_CH11
|
||
14 IO12 I/O GPIO12, ADC2_CH1, TOUCH_CH12
|
||
15 IO13 I/O GPIO13, ADC2_CH2, TOUCH_CH13
|
||
16 IO14 I/O GPIO14, ADC2_CH3, TOUCH_CH14
|
||
17 IO15 I/O GPIO15, ADC2_CH4, XTAL_32K_P
|
||
18 IO16 I/O GPIO16, ADC2_CH5, XTAL_32K_N
|
||
19 IO17 I/O GPIO17, ADC2_CH6, DAC_1
|
||
20 5V0 P 5 V power supply
|
||
21 GND G Ground
|
||
=== ==== ===== ===================================
|
||
|
||
J3
|
||
^^^
|
||
=== ==== ===== ====================================
|
||
No. Name Type Function
|
||
=== ==== ===== ====================================
|
||
1 GND G Ground
|
||
2 RST I CHIP_PU, Reset
|
||
3 IO46 I GPIO46
|
||
4 IO45 I/O GPIO45
|
||
5 IO44 I/O GPIO44, U0RXD
|
||
6 IO43 I/O GPIO43, U0TXD
|
||
7 IO42 I/O GPIO42, MTMS
|
||
8 IO41 I/O GPIO41, MTDI
|
||
9 IO40 I/O GPIO40, MTDO
|
||
10 IO39 I/O GPIO39, MTCK
|
||
11 IO38 I/O GPIO38
|
||
12 IO37 I/O GPIO37
|
||
13 IO36 I/O GPIO36
|
||
14 IO35 I/O GPIO35
|
||
16 IO34 I/O GPIO34
|
||
17 IO33 I/O GPIO33
|
||
17 IO26 I/O GPIO26
|
||
18 IO21 I/O GPIO21
|
||
19 IO20 I/O GPIO20, ADC2_CH3, USB_D+
|
||
20 IO19 I/O GPIO19, ADC2_CH3, USB_D-
|
||
21 IO18 I/O GPIO18, ADC2_CH3, DAC_2
|
||
=== ==== ===== ====================================
|
||
|
||
P: Power supply;
|
||
I: Input;
|
||
O: Output;
|
||
T: High impedance.
|
||
|
||
Pin Layout
|
||
----------
|
||
|
||
.. figure:: ../_static/esp32-s2_saola1_pinlayout.png
|
||
:align: center
|
||
:width: 600
|
||
:alt: ESP32-S2-Saola-1 (click to enlarge)
|
||
:figclass: align-center
|
||
|
||
Strapping Pins
|
||
--------------
|
||
|
||
Some of the GPIO's have important features during the booting process. Here is the list of the strapping pins on the `ESP32-S2`_.
|
||
|
||
==== ========= ===================================================================== ============ ==============
|
||
GPIO Default Function Pull-up Pull-down
|
||
==== ========= ===================================================================== ============ ==============
|
||
IO45 Pull-down Voltage of Internal LDO (VDD_SDIO) 1V8 3V3
|
||
IO0 Pull-up Booting Mode SPI Boot Download Boot
|
||
IO46 Pull-down Booting Mode Don't Care Download Boot
|
||
IO46 Pull-up Enabling/Disabling Log Print During Booting and Timing of SDIO Slave U0TXD Active U0TXD Silent
|
||
==== ========= ===================================================================== ============ ==============
|
||
|
||
For more detailed information, see the `ESP32-S2`_ datasheet.
|
||
|
||
Restricted Usage GPIOS
|
||
----------------------
|
||
|
||
Some of the GPIO's are used for the external flash and PSRAM. These GPIO's cannot be used:
|
||
|
||
==== ===================
|
||
GPIO Shared Function
|
||
==== ===================
|
||
IO26 Connected to PSRAM
|
||
==== ===================
|
||
|
||
Other GPIO's are `INPUT ONLY` and cannot be used as output pin:
|
||
|
||
==== ===========================
|
||
GPIO Function
|
||
==== ===========================
|
||
IO46 GPIO46
|
||
==== ===========================
|
||
|
||
Resources
|
||
---------
|
||
|
||
* `ESP32-S2`_ (Datasheet)
|
||
* `ESP32-S2-WROVER`_ (Datasheet)
|
||
* `ESP32-S2-Saola-1`_ (Schematics)
|
||
|
||
.. _ESP32-S2: https://www.espressif.com/sites/default/files/documentation/esp32-s2_datasheet_en.pdf
|
||
.. _ESP32-S2-WROVER: https://www.espressif.com/sites/default/files/documentation/esp32-s2-wrover_esp32-s2-wrover-i_datasheet_en.pdf
|
||
.. _ESP32-S2-Saola-1: https://dl.espressif.com/dl/schematics/ESP32-S2-SAOLA-1_V1.1_schematics.pdf
|