81 lines
2.3 KiB
C++
81 lines
2.3 KiB
C++
#if ARDUINO_USB_MODE
|
|
#warning This sketch should be used when USB is in OTG mode
|
|
void setup(){}
|
|
void loop(){}
|
|
#else
|
|
#include "USB.h"
|
|
#include "FirmwareMSC.h"
|
|
|
|
#if !ARDUINO_USB_MSC_ON_BOOT
|
|
FirmwareMSC MSC_Update;
|
|
#endif
|
|
#if ARDUINO_USB_CDC_ON_BOOT
|
|
#define HWSerial Serial0
|
|
#define USBSerial Serial
|
|
#else
|
|
#define HWSerial Serial
|
|
USBCDC USBSerial;
|
|
#endif
|
|
|
|
static void usbEventCallback(void* arg, esp_event_base_t event_base, int32_t event_id, void* event_data){
|
|
if(event_base == ARDUINO_USB_EVENTS){
|
|
arduino_usb_event_data_t * data = (arduino_usb_event_data_t*)event_data;
|
|
switch (event_id){
|
|
case ARDUINO_USB_STARTED_EVENT:
|
|
HWSerial.println("USB PLUGGED");
|
|
break;
|
|
case ARDUINO_USB_STOPPED_EVENT:
|
|
HWSerial.println("USB UNPLUGGED");
|
|
break;
|
|
case ARDUINO_USB_SUSPEND_EVENT:
|
|
HWSerial.printf("USB SUSPENDED: remote_wakeup_en: %u\n", data->suspend.remote_wakeup_en);
|
|
break;
|
|
case ARDUINO_USB_RESUME_EVENT:
|
|
HWSerial.println("USB RESUMED");
|
|
break;
|
|
|
|
default:
|
|
break;
|
|
}
|
|
} else if(event_base == ARDUINO_FIRMWARE_MSC_EVENTS){
|
|
arduino_firmware_msc_event_data_t * data = (arduino_firmware_msc_event_data_t*)event_data;
|
|
switch (event_id){
|
|
case ARDUINO_FIRMWARE_MSC_START_EVENT:
|
|
HWSerial.println("MSC Update Start");
|
|
break;
|
|
case ARDUINO_FIRMWARE_MSC_WRITE_EVENT:
|
|
//HWSerial.printf("MSC Update Write %u bytes at offset %u\n", data->write.size, data->write.offset);
|
|
HWSerial.print(".");
|
|
break;
|
|
case ARDUINO_FIRMWARE_MSC_END_EVENT:
|
|
HWSerial.printf("\nMSC Update End: %u bytes\n", data->end.size);
|
|
break;
|
|
case ARDUINO_FIRMWARE_MSC_ERROR_EVENT:
|
|
HWSerial.printf("MSC Update ERROR! Progress: %u bytes\n", data->error.size);
|
|
break;
|
|
case ARDUINO_FIRMWARE_MSC_POWER_EVENT:
|
|
HWSerial.printf("MSC Update Power: power: %u, start: %u, eject: %u", data->power.power_condition, data->power.start, data->power.load_eject);
|
|
break;
|
|
|
|
default:
|
|
break;
|
|
}
|
|
}
|
|
}
|
|
|
|
void setup() {
|
|
HWSerial.begin(115200);
|
|
HWSerial.setDebugOutput(true);
|
|
|
|
USB.onEvent(usbEventCallback);
|
|
MSC_Update.onEvent(usbEventCallback);
|
|
MSC_Update.begin();
|
|
USBSerial.begin();
|
|
USB.begin();
|
|
}
|
|
|
|
void loop() {
|
|
// put your main code here, to run repeatedly
|
|
}
|
|
#endif /* ARDUINO_USB_MODE */
|