99 lines
3.4 KiB
C
99 lines
3.4 KiB
C
#ifndef Pins_Arduino_h
|
|
#define Pins_Arduino_h
|
|
|
|
#include <stdint.h>
|
|
|
|
#define USB_VID 0x303a
|
|
#define USB_PID 0x1001
|
|
|
|
#define EXTERNAL_NUM_INTERRUPTS 46
|
|
#define NUM_DIGITAL_PINS 48
|
|
#define NUM_ANALOG_INPUTS 20
|
|
|
|
#define analogInputToDigitalPin(p) (((p)<20)?(analogChannelToDigitalPin(p)):-1)
|
|
#define digitalPinToInterrupt(p) (((p)<48)?(p):-1)
|
|
#define digitalPinHasPWM(p) (p < 46)
|
|
|
|
static const uint8_t TX = 43;
|
|
static const uint8_t RX = 44;
|
|
|
|
static const uint8_t SDA = 45;
|
|
static const uint8_t SCL = 46;
|
|
|
|
static const uint8_t SS = 34;
|
|
static const uint8_t MOSI = 35;
|
|
static const uint8_t MISO = 37;
|
|
static const uint8_t SCK = 36;
|
|
|
|
static const uint8_t A0 = 1;
|
|
static const uint8_t A1 = 2;
|
|
static const uint8_t A2 = 3;
|
|
|
|
static const uint8_t T3 = 3;
|
|
|
|
// SDCARD Slot
|
|
#define BOARD_HAS_SDMMC
|
|
#define SDMMC_D2 33 // SDMMC Data2
|
|
#define SDMMC_D3 34 // SDMMC Data3 / SPI CS
|
|
#define SDMMC_CMD 35 // SDMMC CMD / SPI MOSI
|
|
#define SDMMC_CLK 36 // SDMMC CLK / SPI SCK
|
|
#define SDMMC_D0 37 // SDMMC Data0 / SPI MISO
|
|
#define SDMMC_D1 38 // SDMMC Data1
|
|
#define BOARD_MAX_SDMMC_FREQ SDMMC_FREQ_DEFAULT
|
|
|
|
// 240x240 LCD
|
|
#define BOARD_HAS_SPI_LCD
|
|
#define LCD_MODEL ST7789
|
|
#define LCD_WIDTH 240
|
|
#define LCD_HEIGHT 240 // *RAM height is actually 320!
|
|
#define LCD_MISO -1 // LCD Does not use MISO.
|
|
#define LCD_DC 4 // Used to switch data and command status.
|
|
#define LCD_CS 5 // used to enable LCD, low level to enable.
|
|
#define LCD_CLK 6 // LCD SPI Clock.
|
|
#define LCD_MOSI 7 // LCD SPI MOSI.
|
|
#define LCD_RST 8 // used to reset LCD, low level to reset.
|
|
#define LCD_BL 9 // LCD backlight control.
|
|
|
|
// Buttons
|
|
#define BUTTON_OK 0 // OK button, low level when pressed.
|
|
#define BUTTON_UP 10 // UP button, low level when pressed.
|
|
#define BUTTON_DOWN 11 // Down button, low level when pressed.
|
|
#define BUTTON_MENU 14 // Menu button, low level when pressed.
|
|
|
|
// LEDs
|
|
#define LED_GREEN 15 // the light is lit when set high level.
|
|
#define LED_YELLOW 16 // the light is lit when set high level.
|
|
|
|
// Board Controls
|
|
#define DEV_VBUS_EN 12 // High level to enable DEV_VBUS power supply.
|
|
#define BOOST_EN 13 // High level to enable Battery Boost circuit.
|
|
#define LIMIT_EN 17 // Enable USB_HOST current limiting IC, high level enable.
|
|
#define USB_HOST_EN 18 // Used to switch the USB interface. When high level, the USB_HOST interface is enabled. When low level, the USB_DEV interface is enabled.
|
|
|
|
// Board Sensors
|
|
#define OVER_CURRENT 21 // Current overrun signal, high level means overrun.
|
|
#define HOST_VOLTS 1 // USB_DEV voltage monitoring, ADC1 channel 0. actual_v = value_v * 3.7
|
|
#define BAT_VOLTS 2 // Battery voltage monitoring, ADC1 channel 1. actual_v = value_v * 2
|
|
|
|
// USB Port
|
|
#define USB_DN 19 // USB D-
|
|
#define USB_DP 20 // USB D+
|
|
|
|
// Bottom header
|
|
#define MTCK 39
|
|
#define MTDO 40
|
|
#define MTDI 41
|
|
#define MTMS 42
|
|
// #define FREE_6 3 // Idle, can be customized.
|
|
// #define FREE_4 26 // Idle, can be customized.
|
|
// #define FREE_1 45 // Idle, can be customized.
|
|
// #define FREE_2 46 // Idle, can be customized.
|
|
// #define FREE_5 47 // Idle, can be customized.
|
|
// #define FREE_3 48 // Idle, can be customized.
|
|
|
|
typedef enum { USB_HOST_POWER_OFF, USB_HOST_POWER_VBUS, USB_HOST_POWER_BAT } UsbHostPower_t;
|
|
void usbHostPower(UsbHostPower_t mode);
|
|
void usbHostEnable(bool enable);
|
|
|
|
#endif /* Pins_Arduino_h */
|