80 lines
2.5 KiB
C++
80 lines
2.5 KiB
C++
/*
|
|
This example generates a square wave based tone at a specified frequency
|
|
and sample rate. Then outputs the data using the I2S interface to a
|
|
MAX08357 I2S Amp Breakout board.
|
|
|
|
I2S Circuit:
|
|
* Arduino/Genuino Zero, MKR family and Nano 33 IoT
|
|
* MAX08357:
|
|
* GND connected GND
|
|
* VIN connected 5V
|
|
* LRC connected to pin 0 (Zero) or 3 (MKR), A2 (Nano) or 25 (ESP32)
|
|
* BCLK connected to pin 1 (Zero) or 2 (MKR), A3 (Nano) or 5 (ESP32)
|
|
* DIN connected to pin 9 (Zero) or A6 (MKR), 4 (Nano) or 26 (ESP32)
|
|
|
|
DAC Circuit:
|
|
* ESP32 or ESP32-S2
|
|
* Audio amplifier
|
|
- Note:
|
|
- ESP32 has DAC on GPIO pins 25 and 26.
|
|
- ESP32-S2 has DAC on GPIO pins 17 and 18.
|
|
- Connect speaker(s) or headphones.
|
|
|
|
created 17 November 2016
|
|
by Sandeep Mistry
|
|
For ESP extended
|
|
Tomas Pilny
|
|
2nd September 2021
|
|
*/
|
|
|
|
#include <I2S.h>
|
|
const int frequency = 440; // frequency of square wave in Hz
|
|
const int amplitude = 500; // amplitude of square wave
|
|
const int sampleRate = 8000; // sample rate in Hz
|
|
const int bps = 16;
|
|
|
|
const int halfWavelength = (sampleRate / frequency); // half wavelength of square wave
|
|
|
|
short sample = amplitude; // current sample value
|
|
int count = 0;
|
|
|
|
i2s_mode_t mode = I2S_PHILIPS_MODE; // I2S decoder is needed
|
|
// i2s_mode_t mode = ADC_DAC_MODE; // Audio amplifier is needed
|
|
|
|
// Mono channel input
|
|
// This is ESP specific implementation -
|
|
// samples will be automatically copied to both channels inside I2S driver
|
|
// If you want to have true mono output use I2S_PHILIPS_MODE and interlay
|
|
// second channel with 0-value samples.
|
|
// The order of channels is RIGH followed by LEFT
|
|
//i2s_mode_t mode = I2S_RIGHT_JUSTIFIED_MODE; // I2S decoder is needed
|
|
|
|
void setup() {
|
|
Serial.begin(115200);
|
|
Serial.println("I2S simple tone");
|
|
|
|
// start I2S at the sample rate with 16-bits per sample
|
|
if (!I2S.begin(mode, sampleRate, bps)) {
|
|
Serial.println("Failed to initialize I2S!");
|
|
while (1); // do nothing
|
|
}
|
|
}
|
|
|
|
void loop() {
|
|
if (count % halfWavelength == 0 ) {
|
|
// invert the sample every half wavelength count multiple to generate square wave
|
|
sample = -1 * sample;
|
|
}
|
|
|
|
if(mode == I2S_PHILIPS_MODE || mode == ADC_DAC_MODE){ // write the same sample twice, once for Right and once for Left channel
|
|
I2S.write(sample); // Right channel
|
|
I2S.write(sample); // Left channel
|
|
}else if(mode == I2S_RIGHT_JUSTIFIED_MODE || mode == I2S_LEFT_JUSTIFIED_MODE){
|
|
// write the same only once - it will be automatically copied to the other channel
|
|
I2S.write(sample);
|
|
}
|
|
|
|
// increment the counter for the next sample
|
|
count++;
|
|
}
|