xPablo.cz/arduino-esp32-custom-lwip-ppp-enabled
2
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
master
arduino-esp32-custom-lwip-p.../docs/EXAMPLE_README_TEMPLATE.md

4.4 KiB
Raw Permalink Blame History

Arduino-ESP32 Example/Library Name ==(REQUIRED)==

==Add a brief description about this example/library here!==

This example/library demonstrates how to create a new example README file.

Supported Targets ==(REQUIRED)==

==Add the supported devices here!==

Currently, this example supports the following targets.

Supported Targets ESP32 ESP32-S2 ESP32-C3

How to Use Example/Library ==(OPTIONAL)==

==Add a brief description on how to use this example.==

Hardware Connection ==(OPTIONAL)==

==Add a brief description about wiring or any other hardware specific connection.==

To use this example, you need to connect the LED to the GPIOx.

SDCard GPIO connection scheme:

SDCard Pin Function GPIO
1 CS GPIO5
2 DI/MOSI GPIO23
3 VSS/GND GND
4 VDD/3V3 3V3
5 SCLK GPIO18
6 VSS/GND GND
7 DO/MISO GPIO19

To add images, please create a folder _asset inside the example folder to add the relevant images.

Configure the Project ==(OPTIONAL)==

==Add a brief description about this example here!==

Set the LED GPIO by changing the LED_BUILTIN value in the function pinMode(LED_BUILTIN, OUTPUT);. By default, the GPIO is: GPIOx.

Example for the GPIO4:

==Add some code explanation if relevant to the example.==

// the setup function runs once when you press reset or power the board
void setup() {
// initialize digital pin 4 as an output.
pinMode(4, OUTPUT);
}

Using Arduino IDE

To get more information about the Espressif boards see Espressif Development Kits.

  • Before Compile/Verify, select the correct board: Tools -> Board.
  • Select the COM port: Tools -> Port: xxx where the xxx is the detected COM port.

Using Platform IO

  • Select the COM port: Devices or setting the upload_port option on the platformio.ini file.

Example/Log Output ==(OPTIONAL)==

==Add the log/serial output here!==

ets Jul 29 2019 12:21:46

rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:1
load:0x3fff0030,len:1412
load:0x40078000,len:13400
load:0x40080400,len:3672
entry 0x400805f8
ESP32 Chip model = ESP32-D0WDQ5 Rev 3
This chip has 2 cores
Chip ID: 3957392

Troubleshooting ==(REQUIRED)==

==Add specific issues you may find by using this example here!==

Important: Make sure you are using a good quality USB cable and that you have a reliable power source

  • LED not blinking: Check the wiring connection and the IO selection.
  • Programming Fail: If the programming/flash procedure fails, try reducing the serial connection speed.
  • COM port not detected: Check the USB cable and the USB to Serial driver installation.

If the error persist, you can ask for help at the official ESP32 forum or see Contribute.

Contribute ==(REQUIRED)==

==Do not change! Keep as is.==

To know how to contribute to this project, see How to contribute.

If you have any feedback or issue to report on this example/library, please open an issue or fix it by creating a new PR. Contributions are more than welcome!

Before creating a new issue, be sure to try the Troubleshooting and to check if the same issue was already created by someone else.

Resources ==(REQUIRED)==

==Do not change here! Keep as is or add only relevant documents/info for this example. Do not add any purchase link/marketing stuff==